Search results

First off I apologize if this is in the wrong section and if so please move it to the correct section. So after battling severe Rheumatoid Arthritis for the past 10 years and seeing multiple doctors I found out my only real option to be in less/no pain is total wrist fusion. Now it wouldn't be...

Yesterday when I was riding my bike to my parents house after riding it all day it broke down on me. At first I thought it was the battery as I know it's needed a new one for a while. Once I got a new battery and realized I had to charge it first I trailered the bike to my parents, put it on...

I have another set of clip ons that I found in my parts bins. They are 32mm Tommaselli adjustable clip ons. On has minor scratches on it and the other has only been taken out of the bag for the pic. I would like $50 shipped to the US. The bottom looks like it has mold or something on it but...

I was surfing ebay and saw a hydraulic clutch conversion. Any one ever seen or used one of these? I've been doing some research and haven't been able to find much info on it. Here's a link...

I have some 34mm clip on clamps, pretty much the clip ons without the bars. They use 7/8in bars. I think I have the bars around here some where but can't find them at the moment. If I do I'll include them for the price. If not it's just for the clamps. I'd like to get $50 shipped any where in...

I have a set of 33mm Tarozzi low rise adjustable clip ons that I don't need any more. These are used and show minor signs of wear. I will take pics later when I get home. I want $90 shipped OBO. I'd also consider trades for CB350 stuff like carb diaphragms or other things, just let me know what...

So it's been a while since I have been able to ride my bike due to some injuries and then about a month ago I got laid off at work. But I finally am better and have been working on the bike for a while. A little back ground on the bike. It is a 73 CB350G. I completely rebuilt the carbs and put a...

Today when I took my 73' cb350g out for a test ride I noticed my caliper was sticking. It's like when I apply the brakes the pads don't retract and continue to rub on the rotor. It was so bad that it caused a small grove to form and the rotor to change colors, like when stainless steel gets...

I did try searching before I posted this and could not find anything. Today when I took my 73 cb350 g for a test ride I noticed I only have about 3/4 - 1 inch of travel from the clutch not being engaged to fully engaged. I've tried adjusting it multiple times and have gotten the same results...

I need the pegs with cross bar and side stand. I also need a keyed seat latch and key for a flip to side seat. Thanks in advance.

I was digging through my parts bin and came across a box that has two almost complete Dyna III electronic ignition set-ups minus the rotors. I think I bought them a few years back as they were advertised for a cb350 but think they were for a cb350/450 F. The problem I have is they do not fit...

Hey guys. So yesterday I went to put my center stand back on my 73' CB350G, because the side stand gets in the way of my rear sets, and it seems like the stand might be bent or something. It doesn't fit around the chain any more. I know it fit on the bike properly before I took it all down but...

I need a set of decent cb350 twin carbs. Either already rebuilt or rebuildable. Please let me know what you have and how much. Either reply here, pm me, or send me an e-mail to neuba84@aol.com. Thanks in advance. -Jon

I seem to have missplaced the banjo bolt for my cb350g and have not been able to find one localy. I can get one with the right thread just too long. Does any one know if I could just cut down a longer banjo bolt or is that not a good idea? If you don't recomend doing that does any one know of...

So I started to tear my carbs apart for my cb350 and they are toast. They have a million pin holes in the bowls and just unrebuildable. I had a buddy of mine who is a motorcycle mechanic look at them and he told me the same thing. So my question is will any carbs off of any other bike bolt right...

What's goin on guys. I've been lurking on this board for quite a while and finally am able to really work on my build. I bought this bike a couple of years ago and stripped most of the tabs off of it and stripped the frame down to bare metal. I then primed it with rattle can acid etching...

What's up guys? I've been lurking and admiring all of ya'll's builds. I'm currently building a 73 CB350 G. I've been building this bike off and on for the past 3 years or so. I've been held up by multiple things like finishing school, getting into a new career, buying a house, getting married...